<noautolink>

#ReleaseContents

Release Contents

See GSRD v14.0.2 - Release Notes

<nop>SoCFPGA Linux kernel

MAL

1. Location (mach-<nop>SoCFPGA)

2. Supported features

3. Device tree entries

The <nop>SoCFPGA kernel enables SMP by default. Check out the next section to turn off SMP if you need.

Turning off SMP

There are two ways to achieve this.

Changing the kernel command line

The kernel reads a command line at boot time, the command line is a list of arguments that define the behavior of the kernel.

This includes:

• the speed of the UART console,
• the NFS settings (when the root file system is mounted over the network)
• the number of CPU's the kernel can use

The number of CPU's the kernel can use at run time is defined by the command line argument 'maxcpus'.

So, to run the <nop>SoCFPGA Linux kernel in Uni-Processor mode, change the kernel command line as follows:

bootargs = "console=ttyS0,115200 maxcpus=1"

The command line can be found in the DTS (device tree source) file. That file is generated with the Device Tree Generator by using the board information XML file. You will need to edit the board configuration XML file, invoke the make utility in the GHRD folder to re-generate the Device Tree Source and compile it into the Device Tree Blob, then put it on the SD Card.

See Device Tree Generator User Guide for more information about the Device Tree Generator.

Changing the kernel configuration

The default !<nop>SoCFPGA kernel configuration enables SMP. This can be turned off by editing the configuration (see instructions below).

To modify the kernel configuration, following this procedure:

bitbake -c menuconfig -f virtual/kernel

This will open the configuration menu of the kernel. Turn off the option 'Symmetric Multiprocessing' (under 'Kernel Features'), save the configuration and rebuild the kernel

bitbake -f -c compile virtual/kernel && bitbake -f -c deploy virtual/kernel 

Clock tree

1. location of the clock tree driver

2. Features

3. Device tree entries

Drivers

UART

1. Location of the driver

   • linux/drivers/tty/serial/8250/8250_dw.c

2. Integration into the kernel:

   • TTY

3. Device tree bindings are documented in:

   • linux/Documentation/devicetree/bindings/i2c/i2c-designware.txt

4. Supported features

   • Unchanged from the community driver

5. Defconfig settings

   • CONFIG_SERIAL_8250=y
   • CONFIG_SERIAL_8250_CONSOLE=y
   • CONFIG_SERIAL_8250_NR_UARTS=2
   • CONFIG_SERIAL_8250_RUNTIME_UARTS=2
   • CONFIG_SERIAL_8250_DW=y

I2C

1. Location of the driver

   • linux/drivers/i2c/busses/i2c-designware-core.c
   • linux/drivers/i2c/busses/i2c-designware-core.h
   • linux/drivers/i2c/busses/i2c-designware-pcidrv.c
   • linux/drivers/i2c/busses/i2c-designware-platdrv.c

2. Integration into the kernel:

   • I2C

3. Device tree bindings are documented in:

   • linux/Documentation/devicetree/bindings/i2c/i2c-designware.txt

4. Supported features

   • Added speed setting to device tree.
   • I2C bus on DesignWare adapter.

5. Defconfig settings

   • CONFIG_I2C=y
   • CONFIG_I2C_DESIGNWARE_CORE=y
   • CONFIG_I2C_DESIGNWARE_PLATFORM=y
   • CONFIG_I2C_CHARDEV=y

LCD

1. Location of the driver

   • linux/drivers/tty/newhaven_lcd.c

2. Integration into the kernel:

   • I2C
   • TTY

3. Device tree bindings are documented in:

   • linux/Documentation/devicetree/bindings/tty/newhaven_lcd.txt

4. Supported features

   • Supports the Newhaven NHD\x{2010}0216K3Z\x{2010}NSW\x{2010}BBW 2x16 LCD module as i2c slave.
   • Device will show up as /dev/ttyLCD0
   • Use 'printf' to print ('echo' messes up the required control characters).
   • Backspace is supported to the beginning of the current line.
     • i.e. printf '\b' > /dev/ttyLCD0
   • Erase whole display and reset cursor to home:
     • ESC [ 2 J
     • i.e. printf '\e[2J' > /dev/ttyLCD0
   • Erase current line and set cursor to beginning of line.
     • ESC [ 2 K
     • i.e. printf '\e[2K' > /dev/ttyLCD0
   • CR and LF are supported.
     • i.e. printf 'Hello\nlovely people' > /dev/ttyLCD0
   • Vertical scroll when cursor is on bottom line and receive end of line.

5. Defconfig settings

   • CONFIG_NEWHAVEN_LCD=y

I2C EEPROM

1. Location of the driver
   • linux/drivers/misc/eeprom/at24.c
2. Integraiton into the kernel:
   • I2C
3. Device tree bindings are documented in
   • linux/Documentation/devicetree/bindings/eeprom.txt
4. Supported features
   • Unchanged from the community driver
5. Defconfig settings
   • CONFIG_EEPROM_AT24=y

GPIO

1. Location of the driver

   • linux/drivers/gpio/gpio-dw.c
   • linux/drivers/gpio/gpio-altera.c

2. Integration into the kernel:

   • GPIO

3. Device tree bindings are documented in:

   • linux/Documentation/devicetree/bindings/gpio/gpio-altera.txt

4. Supported features

   • Support Designware gpio and Altera FPGA soft gpio

5. Defconfig settings

   • CONFIG_GPIOLIB=y
   • CONFIG_GPIO_SYSFS=y
   • CONFIG_GPIO_DW=m
   • CONFIG_GPIO_ALTERA=m

Ethernet

1. Location of the driver

   • linux/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c
   • linux/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h
   • linux/drivers/net/ethernet/stmicro/stmmac/dwmac1000_dma.c
   • linux/drivers/net/ethernet/stmicro/stmmac/dwmac100_core.c
   • linux/drivers/net/ethernet/stmicro/stmmac/dwmac100.h
   • linux/drivers/net/ethernet/stmicro/stmmac/dwmac100_dma.c
   • linux/drivers/net/ethernet/stmicro/stmmac/dwmac_lib.c
   • linux/drivers/net/ethernet/stmicro/stmmac/enh_desc.c
   • linux/drivers/net/ethernet/stmicro/stmmac/mmc_core.c
   • linux/drivers/net/ethernet/stmicro/stmmac/mmc.h
   • linux/drivers/net/ethernet/stmicro/stmmac/norm_desc.c
   • linux/drivers/net/ethernet/stmicro/stmmac/descs_com.h
   • linux/drivers/net/ethernet/stmicro/stmmac/stmmac.h
   • linux/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c
   • linux/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
   • linux/drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c
   • linux/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c

2. Integration into the kernel:

   • NET
   • ETHERNET

3. Device tree bindings are documented in:

   • linux/Documentation/devicetree/bindings/net/phy.txt

4. Supported features

   • Mainline DesignWareEthernetdriverplusthesefixes:
     • FogBugz #97997: Fix inifinit interrupt was happening for large files
     • FogBugz #98759: Fix added NFS to kernel to support nfs mount.

5. Defconfig settings

   • CONFIG_STMMAC_ETH

SD/MMC

1. Location of the driver

   • linux/drivers/mmc/host/dw_mmc.c
   • linux/drivers/mmc/host/dw_mmc.h
   • linux/drivers/mmc/host/dw_mmc-pltfm.c
   • linux/drivers/mmc/host/dw_mmc-pltfm.h

2. Integration into the kernel:

   • MMC

3. Device tree bindings are documented in:

   • linux/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt

4. Supported features

   • Mainline DesignWareMMCdriverplusthesefixes:
     • FogBugz #91445: Fix intermittent data starvation for DMA on SD/MMC
     • FogBugz #90657: Fix SD/MMC driver for VT

5. Defconfig settings

   • CONFIG_MMC=y
   • CONFIG_MMC_DW=y
   • CONFIG_MMC_DW_IDMAC=y

Boot Loader (U-Boot)

MAL

The version of bootloader (U-Boot) for this release is V2013.01.

Below are the features supported for this release:

1. Support SDMMC boot include write support
2. Support QSPI boot include write and erase support
3. Ethernet TFTP support
4. FPGA programming support
5. Both instruction and data cache enabled
6. Support Virtual Platform and Dev Kit

Note:
U-Boot will depend the clock information from the pll_config.h (handoff info provided by tools)
During the exit of Preloader, the watchdog is enabled. Bootloader need to pet or disable the watchdog upon entry.

Drivers

UART

1. Location of the driver
   u-boot/drivers/serial/ns16550.c
   .
2. Configuration
   Through macros defined at include/configs/<nop>SoCFPGA_cyclone5.h
   CONFIG_SYS_NS16550
   CONFIG_SYS_NS16550_SERIAL
   CONFIG_SYS_NS16550_REG_SIZE
   CONFIG_SYS_NS16550_CLK
   CONFIG_CONS_INDEX 1
   CONFIG_SYS_NS16550_COM1
   CONFIG_SYS_BAUDRATE_TABLE
   CONFIG_BAUDRATE
   .
   Through handoff info provided by tools
   CONFIG_HPS_CLK_L4_SP_HZ (from board/altera/<nop>SoCFPGA_cyclone5/pll_config.h)
   .
3. Supported features
   Standard RS232 communication protocol

Ethernet

1. Location of the driver
   u-boot/drivers/net/designware.c
   .
2. Configuration macros
   Through macros defined at include/configs/<nop>SoCFPGA_cyclone5.h
   CONFIG_EMAC0_BASE
   CONFIG_EMAC1_BASE
   CONFIG_CMD_NET
   CONFIG_CMD_PING
   CONFIG_CMD_DHCP
   CONFIG_NET_MULTI
   CONFIG_DW_ALTDESCRIPTOR
   CONFIG_EPHY0_PHY_ADDR
   CONFIG_EPHY1_PHY_ADDR
   CONFIG_DW_SEARCH_PHY
   CONFIG_MII
   CONFIG_CMD_MII
   CONFIG_PHY_GIGE
   CONFIG_DW_AUTONEG
   CONFIG_AUTONEG_TIMEOUT
   .
3. Supported features
   RGMII support

SD/MMC

1. Location of the driver
   u-boot/drivers/mmc/dw_mmc.c
   .
2. Configuration macros
   Through macros defined at include/configs/<nop>SoCFPGA_cyclone5.h
   CONFIG_MMC
   CONFIG_SDMMC_BASE
   CONFIG_SDMMC_HOST_HS
   CONFIG_GENERIC_MMC
   CONFIG_DW_MMC
   .
   Through handoff info provided by tools
   CONFIG_HPS_CLK_SDMMC_HZ (from board/altera/<nop>SoCFPGA_cyclone5/pll_config.h)
   CONFIG_HPS_SDMMC_BUSWIDTH(from board/altera/<nop>SoCFPGA_cyclone5/pinmux_config.h)
   .
3. Supported features
   - Read and write support
   - Support SDHC, SD High Speed (not validated) and MMC (not validated)

QSPI

1. Location of the driver
   u-boot/drivers/spi/cadence_qspi.c
   u-boot/drivers/spi/cadence_qspi_apb.c
   .
2. Configuration macros
   Through macros defined at include/configs/<nop>SoCFPGA_cyclone5.h
   CONFIG_CADENCE_QSPI
   CONFIG_CQSPI_BASE
   CONFIG_CQSPI_AHB_BASE
   CONFIG_SPI_FLASH
   CONFIG_SPI_FLASH_STMICRO
   CONFIG_SF_DEFAULT_SPEED
   CONFIG_SF_DEFAULT_MODE
   CONFIG_SPI_FLASH_QUAD
   CONFIG_CQSPI_REF_CLK
   CONFIG_CQSPI_PAGE_SIZE
   CONFIG_CQSPI_BLOCK_SIZE
   CONFIG_CQSPI_DECODER
   CONFIG_CQSPI_4BYTE_ADDR
   
   /* QSPI Delay timing */
   CONFIG_CQSPI_TSHSL_NS
   CONFIG_CQSPI_TSD2D_NS
   CONFIG_CQSPI_TCHSH_NS
   CONFIG_CQSPI_TSLCH_NS
   CONFIG_CQSPI_READDATA_DELAY
   .
   Through handoff info provided by tools
   CONFIG_HPS_CLK_QSPI_HZ (from board/altera/<nop>SoCFPGA_cyclone5/pll_config.h)
   .
3. Supported features
   - Read, write and erase support
   - Quad mode support
   - Support external decoder for chip select

FPGA

1. Location of the driver
   u-boot/arch/arm/cpu/armv7/<nop>SoCFPGA/fpga_manager.c
   .
2. Configuration macros
   Through macros defined at include/configs/<nop>SoCFPGA_cyclone5.h
   CONFIG_FPGA
   CONFIG_FPGA_ALTERA
   CONFIG_FPGA_<nop>SoCFPGA
   CONFIG_FPGA_COUNT
   CONFIG_CMD_FPGA
   .
3. Supported features
   - FPGA programming
   - Support normal and compression FPGA configuration files

U-boot Configuration Support

Default configuration

Below are the U-Boot environment's default value. These environments was defined at include/configs/socfpga_cyclone5.h.
"verify=n\0"
"loadaddr=" MK_STR(CONFIG_SYS_LOAD_ADDR) "\0"
"fdtaddr=0x00000100\0"
"bootimage=uImage\0"
"bootimagesize=0x600000\0"
"fdtimage=socfpga.dtb\0"
"fdtimagesize=0x2000\0"
"mmcloadcmd=fatload\0"
"mmcloadpart=1\0"
"mmcroot=/dev/mmcblk0p2\0"
"qspiloadcs=0\0"
"qspibootimageaddr=0xa0000\0"
"qspifdtaddr=0x50000\0"
"qspiroot=/dev/mtdblock1\0"
"qspirootfstype=jffs2\0"
"ramboot=setenv bootargs " CONFIG_BOOTARGS "; bootm ${loadaddr} - ${fdtaddr}\0"
"mmcload=mmc rescan;${mmcloadcmd} mmc 0:${mmcloadpart} ${loadaddr} ${bootimage}; ${mmcloadcmd} mmc 0:${mmcloadpart} ${fdtaddr} ${fdtimage}\0"
"mmcboot=setenv bootargs " CONFIG_BOOTARGS " root=${mmcroot} rw rootwait; bootm ${loadaddr} - ${fdtaddr}\0"
"netboot=dhcp ${bootimage} ; tftp ${fdtaddr} ${fdtimage} ; run ramboot\0"
"qspiload=sf probe ${qspiloadcs}; sf read ${loadaddr} ${qspibootimageaddr} ${bootimagesize}; sf read ${fdtaddr} ${qspifdtaddr} ${fdtimagesize};\0"
"qspiboot=setenv bootargs " CONFIG_BOOTARGS " root=${qspiroot} rw rootfstype=${qspirootfstype}; bootm ${loadaddr} - ${fdtaddr}\0"
"fpga=0\0"
"fpgadata=0x2000000\0"
"fpgadatasize=0x700000\0"

Configuration modifications

You can modify the U-Boot configuration during run time.
To do that, you can use below commands
% env set <environment variable> <value>
% saveenv</noautolink>